Saniel D. Lim
Lecturer
- Milwaukee WI UNITED STATES
- Mechanical Engineering
Dr. Saniel Lim teaches in the Mechanical Engineering Department at MSOE.
Education, Licensure and Certification
Ph.D.
University of Washington
Mechanical Engineering
2020
Dissertation Title: Design and Fabrication of Optomechanical Formalin Fixation Monitoring Systems Integrated with a Millifluidic Device
M.S.
North Carolina State University
Mechanical Engineering
2013
B.S.
Ajou University
Mechanical Engineering
2006
Biography
Industry Expertise
Areas of Expertise
Accomplishments
Image - based Biomechanics Modeling Graduate Assistance in Areas of National Need (GAANN) Fellowship
2013 – 2016
Research Assistantship
2011 – 2013
North Carolina Coastal Studies Institute
Social
Selected Publications
Proof of Concept of a Surrogate High-Adhesion Medical Tape Using Photo-Thermal Release for Rapid and Less Painful Removal
Journal of Medical Devices2020
Medical tapes often hold critical devices to the skin so having high adhesion for the lifespan of this product is of great importance. However, the removal process is challenging for caregivers and patients alike, often a painful process that can cause medical adhesive-related skin injury (MARSI). By using an industrial thermally sensitive tape, a surrogate photosensitive tape was developed that switched from the equivalent of high-adhesion medical tape to low-adhesion medical tape.
Evaluation of Formalin Fixation for Tissue Biopsies Using Shear Wave Laser Speckle Imaging System
IEEE Journal of Translational Engineering in Health and Medicine2019
Chemical fixation is the slowest and often the most uncontrolled step in the multi-step process of preparing tissue for histopathology. In order to reduce the time from taking a core needle biopsy to making a diagnosis, a new approach is proposed that optically monitors the common formalin fixation process. A low-cost and highly-sensitive laser speckle imaging technique is developed to measure shear wave velocity in a biospecimen as small as 0.5 mm in thickness submerged in millifluidic channels.
Pathology in a tube step 2: simple rapid fabrication of curved circular cross section millifluidic channels for biopsy preparation/3D imaging towards pancreatic cancer detection and diagnosis
Proceedings Volume 10491, Microfluidics, BioMEMS, and Medical Microsystems XVI; 1049118 (2018) https://doi.org/10.1117/12.2291018Das, R., Burfeind, C. W., Lim, S. D., Patle, S., Seibel, E. J.
2018
3D pathology is intrinsically dependent on 3D microscopy, or the whole tissue imaging of patient tissue biopsies (TBs). Consequently, unsectioned needle specimens must be processed whole: a procedure which cannot necessarily be accomplished through manual methods, or by retasking automated pathology machines. Thus "millifluidic" devices (for millimeter-scale biopsies) are an ideal solution for tissue handling/preparation. TBs are large, messy and a solid-liquid mixture; they vary in material, geometry and structure based on the organ biopsied, the clinician skill and the needle type used. As a result, traditional microfluidic devices are insufficient to handle such mm-sized samples and their associated fabrication techniques are impractical and costly with respect to time/efficiency. Our research group has devised a simple, rapid fabrication process for millifluidic devices using jointed skeletal molds composed of machined, reusable metal rods, segmented rods and stranded wire as structural cores; these cores are surrounded by Teflon outer housing. We can therefore produce curving, circular-cross-section (CCCS) millifluidic channels in rapid fashion that cannot normally be achieved by microfabrication, micro-/CNC-machining, or 3D printing. The approach has several advantages. CLINICAL: round channels interface coring needles. PROCESSING: CCCS channels permit multi-layer device designs for additional (processing, monitoring, testing) stages. REUSABILITY: for a biopsy/needle diameter, molding (interchangeable) components may be produced one-time then reused for other designs. RAPID: structural cores can be quickly removed due to Teflon®'s ultra-low friction; housing may be released with ethanol; PDMS volumes cure faster since metal skeleton molds conduct additional heat from within the curing elastomer.
Conceptual Design of Ocean Compressed Air Energy Storage System
Marine Technology Society Journal2013
In this paper, an ocean compressed air energy storage (OCAES) system is introduced as a utility-scale energy storage option for electricity generated by wind, ocean currents, tides, and waves off the coast of North Carolina. Geographically, a location from 40 to 70 km off the coast of Cape Hatteras is shown to be a good location for an OCAES system.